GREENSHIELD ECOLOGICAL INSULATION PLASTER

Premixed insulation plaster providing thermal, water and sound insulation and fire resistance on the buildings to which it is applied, without requiring any other plaster, primer, adhesive or additional insulation products for new or old buildings. It can be applied various substrates like brick, autoclaved aerated concrete, concrete, precast concrete panel or stone. Due to its homogenous structure and ease of application similar to plaster, it can be controlled easily. The application mistakes and damages occurred afterwards can also easily be repaired. It can be applied by machine for the large surfaces. So provides savings on workmanship and time through its ease of application. On the buildings having problems to apply for facade, it may also be applied on the interior walls.

Local repairs can easily be carried out on the surfaces to which it is applied. The insulation performance is being protected via local repairs performed on the surface problems caused by the exterior factors or any other different circumstances.

As it does not absorb the water, it avoids the cracks and spalling caused by the changes in weather conditions.

>Product Description

Inorganic material-based insulation material in granulometric powder form, modified with minerals, for thermal, water, sound insulation and fire resistance which is applied in plaster form on to the building walls directly without any extra process.

  • Color: White

>Application Fields

Applied on to the exterior or interior wall of both new and old buildings in order to provide insulation.

Applicable to following surfaces;
  • Brick
  • Aerated Concrete
  • Pumice Block / Brick
  • Precast Concrete
  • Concrete
  • Natural Stone


Performance Values

Durum DeÄŸer
Dry Bulk Weight: 330 kg/m3 +/- 30
Thermal Conductivity: 0,041 W/mK (T1)
Reaction to Fire Class: A1
Capillary Water absorption: 0,2 (W1)
Vapor Permeability Coefficient < 4,7
Compressive Strength: 1,3 MPa (CSI)
Flexural Strength: 0,6 MPa
Adhesion to Substrate: 0,32 N/mm2 - 100% CF-A

>Application Thickness

Application thickness is determined in accordance to the regional weather conditions, wall structure and insulation level required or demanded. So our experts will assist you to determine the suitable application thickness for your building.

Limitations for Application Thickness:
  • Minimum Application Thickness: 5 mm
  • Maximum Application Thickness: 100 mm
  • Maximum thickness to be used at a time: 30 mm
  •  
  • (For the thickness requirements above 30 mm, it should be waited for 12 hours after each layer. This period can be extended on cold weather conditions.)

Surface Preparation:
  • It is required to remove and clean the dust on surface on which insulation material is to be applied.
  • It is not required to use any primer or auxiliary material on the surface on which insulation material is to be applied.
  • Present paint on surface shall be peeled off from the wall before the application on the old buildings.

>Application Methods

Greenshield Natural Insulation Plaster can be applied by both manually and machine.

1.Manual Application

  • Pour one package Greenshield into a clean bucket of 30-40 liter
  • Add approximately 6-7 liters of water into the bucket.
  • Mix it with plaster mixer for 7-8 minutes until it reachs the consistency of plaster, than it is ready to apply.
    Resimler: Karıştırma resmi, kıvam resmi.
  • * In order to provide the required thickness and to have a straight wall, the laths are mounted vertically on to the wall at certain gaps as wide as the straight edge.
  • Prepared plaster is applied by a suitable trowel roughly between the laths.
  • The surface is leveled by straight edge.
  • After the surface absorbs the water in a certain period of time, one of the following processes is performed preferably;
    • Alternative 1: Process is finished by leveling the surface with steel trowel.
    • Alternative 2: Process is finished by applying 1-3 mm thick decorative plaster to the surface as a finishing coat.
    • Resimler: El ile sıva uygulanırken, mastar çekilirken

Machine application

Material can also be applied to the surfaces by plastering machines. It is not required any other special machine.

  • In order to provide the required thickness and to have a straight wall, the laths are mounted vertically on to the wall at certain gaps as wide as the straight edge.
  • One pack of product is poured into the plastering machine.
  • The automatic water adjustment is the most important point here. Approximately 1/3 of the water which is already being used in standard plaster application shall be used in the plastering machine.
  • If the water content of the material is too much, the water level is decreased until it becomes thicken like plaster.
  • Then, the product roughly poured between laths by machine.
  • The surface is leveled by straight edge.
  • After the surface absorbs the water in a certain period of time, one of the following processes is performed preferably;
    • Alternative 1: Process is finished by leveling the surface with steel trowel.
    • Alternative 2: Process is finished by applying 1-3 mm thick decorative plaster to the surface as a finishing coat.

Cautions & Recommendations

  • Packs should be used completely while preparing the mixture. The product in each pack should completely be poured.
  • It is required to pay attention to the water amount to be added into the mixture. Excessive amount of water should not be added.
  • Any different materials other than water should definitely not be added into the mixture.
  • The mixture shall be prepared with suitable plastering mixer under low-speed during the recommended period of time.
  • Plastering mesh should be used for the buildings having 30-storey and more, against the negative effects of the wind load. In lower buildings it is not required to use plastering mesh.
  • Using of plastering mesh is recommended in the applications having thickness of 40 mm and more.
  • The ambient temperature for the application should be between +5°C and +35 °C.

>Packaging Info



Durum DeÄŸer
Net Package Content : 12 kg of Greenshield Natural Insulation Plaster
Mode of handling : Shrink wrapped on Wooden Pallet
Base Dimension of Pallet Ölçüleri: 100 x 120 cm
Pallet Height 110 – 120 cm
Packs Per Pallet : 48 Packs
Shelf Life : 12 months* under suitable conditions
(* The stated time period starts from the manufacturing date. It should be kept in dry and moisture free environment. Any contact with water should be avoided. Wet products or products which have had water contact should not be used.

> Consumption Info:


approximately 3,5 – 4,5 kg / sqm per 1 cm thickness.

Teknik Tablolar

Thermal Insulation

Provides high level of thermal insulation for both warm and cold weather conditions.

Fire Resistance

A1 Class Non-flammability

Water Insulation

No water absorption due to its hydrophobic structure

Sound Insulation

Provides high level of sound insulation due to its porous structure.

GreenShield’s benefits?

Greenshield is about to be an essential insulation material for the buildings thanks to its lightness, fire resistance and many similar features as such.

Thanks to its vapour diffusivity, it lets the walls it is applied to breathe and prevents mould and condensation on wall surfaces.

As it is one fifth weight of regular cement based mortars, it reduces the building load and contributes to earth quake behaviour of the building.

It is very durable against impacts having a high compressive strength.

Preperation is very easy. Also it can be applied with less effort with its light weight and high adhesive strength, both manually and using machine.

It has all natural ingredients and does not emit any hazardous gas. So it does not have any negative effect for human health.

As the main raw material is obtained by recycled materials, consumption of natural sources is at minimum and does not cause any chemical waste at any stage.

Effective life is equivalent to the life of the building. And it protects the full performance during all life.

It envelopes the building completely, also being able to be applied on any kind of surface, round shape or corners, easily, thanks to its plaster form, and provides a solid insulation for the building preventing thermal bridges.

It provides savings of time and workmanship because it doesn’t need any extra application like rendering, primer, lining etc. before of after applications.

Details

Greenshield Ecological Insulated Lightweight Screed


Insulated Lightweight Screed for indoor floors



Check

Details

Greenshield Ecological Insulation Plaster


Premixed Insulation Plaster for exterior and interior of the walls



Check